S/W 5906 9mm w/3 mags, new grips, holster & new Wolff Service Pack installed
Traded
My 5906 and cash for a Ruger SR 1911 10mm (never had a 10mm before)
Last price reduction:
$400 with 3 mags and holster.
$350 with only 1 mag and no holster.
The 3rd generation S/W 5906 9mm is an all stainless steel model.
Good used condition and very clean.
With the upgrades already done, it needs nothing.
The member I bought it from used, put 400 rounds through it including Fed 147gr HST.
I put a box through it myself but I'm selling it b/c I bought a S/W 4006 around the same time and decided to keep it instead since I'd never had a 40 caliber.
Previous owner completely detail stripped, replaced springs with Wolff service pack type 2, trigger play spring & rivet were replaced as well.
Grips are factory new replacements (a set of old Pachmayrs are included also).
The front sight dot has been painted orange.
Comes w/3 mags total. One is an original S&W 15rd w/new spring and follower.
The other 2 mags are new 17rd MecGar flush fits. All 3 mags ran without issues and lock the slide back.
Also comes with an Azula RH OWB leather holster. Good fitment, but never carried.
Holster is very well made. https://azulagunholsters.com/
This gun is cleaned, lubed and ready to shoot.
Here are some S/W 5906 specifications:
Type: DA-SA semi-automatic, exposed hammer, pistol
Caliber: 9x19mm (9mm Luger)
Length: 7-½”
Height: 5-½”
Width: 1-1/8” across butt
Barrel length: 4”
Weight (empty): 38 ounces (approx.)
Magazine Capacity: 15 round magazine (two 17 round included)
Construction: Stainless steel with hard chromed carbon steel sub-components
Trigger pull: Approximately 14 lbs., DA; approximately 5½ lbs. SA.
Trigger Reset distance: Approximately 1/16”
Safeties: Manual ambidextrous safety-decocking levers on slide; automatic firing pin plunger; magazine disconnect
Sights: Dovetailed front and rear fixed; Novak rear
Production: Approximately 1988-1999
Must have LTCH & IN license.
I live in Wanamaker (SE Indy outside E465).
No shipping: face to face only.
Traded
My 5906 and cash for a Ruger SR 1911 10mm (never had a 10mm before)
Last price reduction:
$400 with 3 mags and holster.
$350 with only 1 mag and no holster.
The 3rd generation S/W 5906 9mm is an all stainless steel model.
Good used condition and very clean.
With the upgrades already done, it needs nothing.
The member I bought it from used, put 400 rounds through it including Fed 147gr HST.
I put a box through it myself but I'm selling it b/c I bought a S/W 4006 around the same time and decided to keep it instead since I'd never had a 40 caliber.
Previous owner completely detail stripped, replaced springs with Wolff service pack type 2, trigger play spring & rivet were replaced as well.
Grips are factory new replacements (a set of old Pachmayrs are included also).
The front sight dot has been painted orange.
Comes w/3 mags total. One is an original S&W 15rd w/new spring and follower.
The other 2 mags are new 17rd MecGar flush fits. All 3 mags ran without issues and lock the slide back.
Also comes with an Azula RH OWB leather holster. Good fitment, but never carried.
Holster is very well made. https://azulagunholsters.com/
This gun is cleaned, lubed and ready to shoot.
Here are some S/W 5906 specifications:
Type: DA-SA semi-automatic, exposed hammer, pistol
Caliber: 9x19mm (9mm Luger)
Length: 7-½”
Height: 5-½”
Width: 1-1/8” across butt
Barrel length: 4”
Weight (empty): 38 ounces (approx.)
Magazine Capacity: 15 round magazine (two 17 round included)
Construction: Stainless steel with hard chromed carbon steel sub-components
Trigger pull: Approximately 14 lbs., DA; approximately 5½ lbs. SA.
Trigger Reset distance: Approximately 1/16”
Safeties: Manual ambidextrous safety-decocking levers on slide; automatic firing pin plunger; magazine disconnect
Sights: Dovetailed front and rear fixed; Novak rear
Production: Approximately 1988-1999
Must have LTCH & IN license.
I live in Wanamaker (SE Indy outside E465).
No shipping: face to face only.
Last edited:
