There are so many variables here that determine cost.I know that these brands use high quality materials for their blade and construction, but how much better can a $200-$300 knife be then one that’s less than $100? If you have one of these brands, or another one similar, how did it handle rough use? Thanks.
Lot of different materials can determine cost. Handles, blade, frame, bushings, bearings, pocket clip, etc etcI know that these brands use high quality materials for their blade and construction, but how much better can a $200-$300 knife be then one that’s less than $100? If you have one of these brands, or another one similar, how did it handle rough use? Thanks.
I think you’d find similar comparisons with a higher end Spyderco alsoI carried a $40 spyderco delica for over a decade and used it daily. I recently upgraded to a benchmade OTF. The main differences I notice are that the fit and quality of the BM components are better and I don't have to sharpen the BM as often as I did the spyderco. I guess one other difference is that I find myself being more careful with the BM. I don't abuse it like I did the spyderco.
A currently have a Buck 292 as my EDC. It was around a $75 knife. It’s held up to abuse quite well. I do a lot of farm work and house work so the thicker blade of ZT would be good for me. I hadn’t heard of that brand so I’m going to go look them up.Lot of different materials can determine cost. Handles, blade, frame, bushings, bearings, pocket clip, etc etc
There are also some Spyderco and Benchmade that are closer to $100.
Don’t forget Buck, Kershaw, ZT, Etc etc
Spyderco traditionally has thinner more slicey blades. ZT has thicker hard use blades. Your everyday use isn’t the same as someone else’s use.
It’s like buying a car or a gun. You have to get the right features for your use, and not every feature helps you specifically.
If you find one you like, let me know. I can order them in pretty quickly and likely save you a little tooA currently have a Buck 292 as my EDC. It was around a $75 knife. It’s held up to abuse quite well. I do a lot of farm work and house work so the thicker blade of ZT would be good for me. I hadn’t heard of that brand so I’m going to go look them up.
absolutely. Heat treat helps too, but most big brands do a decent job at it.I'm pretty sure the type of steel used to make the knife is much more important than who made it when it comes to edge retention.
Spyderco PM2 is probably one of the most popular ones. I always try to keep at least one in stock, but a lot of the variants are out of stock a lot. I'm always keeping an eye out though.Yep, just like buying a firearm, your mission should drive the gear. But in short, I absolutely recommend Spyderco and BM to people. I used cheap knives (such as the S&W brand stuff or CRKT) for years, and for the abusive work I did, they held up pretty well. I had to sharpen them more often because they used a lower grade of steel, but for cutting through freight straps, stripping wire, and generally beating them up, they did very well. But once I discovered how much better Spydie and BM were, there was no going back.
Price held me back for years, but then I took a used BM Mini-Barrage in on trade and it was all over. I started looking at more used options and found that there were several from each company that were reasonably priced even when new (the Delica or Endura, the Griptilian, etc.). I saved up and bought many of them to try and discovered they were phenomenal and well worth the price!
I get pretty deep into knives for awhile, collecting many that are now discontinued (man do I wish BM would bring back the later variants of the AFCK!), but I’ve settled back down to the Delica, Endura, and Stretch (my favorite!) from Spyderco, and the Griptilian and older Presidio from BM for daily carry. I do still have an original Spyderco Gayle Bradley for when I want to be fancy lol. I will be adding another Spydie ParaMilitary2 eventually, but that may be it.
Anyway, you can’t go wrong with either, and they’ll serve you for years to come if you don’t use them as pry bars or screw drivers lol!