I’ve always been a console guy but have recently been thinking about getting a PC to play Hell Let Loose and some other similar games. I don’t know a lot about the performance of some of the components, but would this be enough to reliably run for most games?
16gb ram
512ssd
1tbhdd
Intel i7...
Signed up for my first Appleseed event in a couple of months. Checking here first for a rifle before I build one. Threaded barrel is a plus but not a deal breaker
Located in Demotte/ Jasper county
Travel lake and Porter counties frequently
I have my class A and have been driving for a local beer distributor the last 5 years. I love the job and am happy with the pay and benefits. I have an opportunity to pick up a few weekend loads for my BIL who is an owner operator. It will be hauling grain from a local plant. I’m not sure if it...
I never knew these upper receivers/rifles existed. Has anyone built one? What’s the preferred caliber and barrel length? I have an approved sbr lower so I can go either way.
NIB Taurus TX22C
Bought new in June, haven’t shot it. Just prefer my competition TX.
This model is optic ready and has the slide lightening cuts to help reliability with subsonic ammo.
Box papers and everything from the facrory
Located in Jasper County
Travel NWI frequently
$285
Trade: AR...
I am in the process of submitting an e-file form 1 and I cannot get my finger print file to upload. I had the prints done at a local class 3 dealer and have them on a flash drive. I currently only have a Mac to use, which could be the problem. Is there an application I can use to get this file...
I bought my parents 2001 suburban that has been in storage. The vehicle is 99% rust free and everything works besides the A/C. So far I have confirmed that the system is full and the clutch does kick on when you turn the system on. I get warm/hot air out of the vents and can hear a hissing noise...
Getting ready to submit a form 1 for my first SBR. I’m have two uppers in mind one a 10.5 and the other a 7 inch. This will mostly be fired at ranges under 100 yards, mainly just something to take to the range and have fun with. Is the 7” going to be that much more impractical compared to the...
Stihl MS250
Completely Rebuilt
New:
Piston, Crank, Cylinder
Muffler
Coil, Spark Plug
OEM Air Filter, Fuel Line, Vent Line
Clutch, Clutch Drum, Needle Bearing
16” Bar and Chain
$250 obo
Trade: AR Parts
Looking for 10.5 upper, BCG, Carbine Stock, 20rd Pmags, optic
Located in NWI/Jasper county
First time filling out a Form 1. I’m going to be building a 10.5 inch AR. I’m undecided on what upper I’m going to end up with but when I fill out the paperwork what should I base the measurements off of?
Thule Roof Rack
2 bike rails
1 wheel holders
Good solid roof rack. I’ve had it mounted on my Impreza and had no problems with it.
$100
Trade: red dot, AR mags, 223/5.56 ammo, 9mm ammo.
Located in NWI/Jasper County
Built by me around 2012. Has seen light range use. It just sits in the safe.
RGuns 556 lower
DS Arms 16” 556 carbine upper
CMMG lower parts kit
1/9 twist
Milspec BCG
Magpul Furniture
Rear Magpul buis
2 milspec mags
Located in Jasper County
Travel Lake and Porter counties
$450
LNIB
Bought new during the pandemic and it has sat in the safe since.
Two tone orange and stainless
Factory box and papers
Two magazines
Trade: AR Parts, red dot
$175
Located in Jasper County
Travel Porter and Lake county frequently
Stihl MS250
45.4 cc
New:
OEM air filter and tank vent
Clutch, needle bearing, sprocket
Muffler and gasket
Saw runs, oils and functions like it should. Powerhead only, no bar or chain. Set up to run .325 chain but can run 3/8 picco with a change of the sprocket.
$225
Open to trades
Located...