JeepHammer
SHOOTER
Thanks.
2"x6" hardwood brace under presses, edgeways, with 'Joist Hangers' on both ends, the brace is also screwed to the top. Solid as a rock.
Inset presses at bench level means no bending/stretching, everything within arms reach and the press doesn't get leverage on the bench.
Either your bench beats the press, or your press beats the bench...
I hate it when benches slapping the wall or 'walk' across the floor.
No hip/elbow busters either!
If the entire room was dedicated to reloading, it might be different, but this is a hobby and such I don't care to dedicate a room to reloading I have to serve & support.
If reading made me money & served me, it would be different, but it doesn't.
I use the design with my little case processing equipment since it's cheap & easy to build and works quite well...
These machines are mounted on plates, so they don't torque the bench/top like a pump handle press does, so this particular bench doesn't need an extra under top brace.
Left, case neck qualifier, 95% open necks or better, no kinks means no splits, ejects blanks, loaded rounds, .204 Ruger, .222 etc.
Middle, case roller. Restores the extraction rim & groove, takes lower case bloat out from sloppy chambers (something no top down die can do),
Right, slow driven Dillon Super 1050, slow drive because the trimmer needs time to work, and the shoulder (Datum length) gets back to where it belongs.
The drawer under the top has all the spare parts, stuff I'm not using currently, and caliber changes.
Still PLENTY of storage on the floor under the bench for buckets & other misc. stuff, 8 sq.ft. footprint and moves easily on a roller dolly.
Casters could easily be installed, but I like it sitting solidly on the floor.
When you reload at home and can stop/walk away when it suits you, standing over a conventional bench with raised press might be OK.
I'm disabled, replacement knees, one hip, enough exotic metal in my back to build a small spacecraft out of, so I sit and I want to reach everything from a comfortable, supportive chair...
AND,
When I'm processing brass as a business it's several hours at a JOB, no getting up and walking off.
The bench tops/presses are at optimum height for me sitting in a supportive chair.
When manually operated, the handle is never higher than my shoulder, and I never have to lean forward and 'Stoop' to complete the stroke.
Feet are flat on the floor, chair has a backrest, and is solid, good for hours without damaging myself or 'Limp Wristing' or short stroking the press.
The XL650 loads MUCH better quality, more consistent ammo than the 1050, while the 1050 has the strength/rigidity to whip stubborn brass.
Brass going back into the same firearm doesn't need a lot of bending, but general brass and milbrass takes a TOUGH press to beat it.
With a little tuning, I haven't seen a 650 that won't produce match grade ammo and decent dies.
2"x6" hardwood brace under presses, edgeways, with 'Joist Hangers' on both ends, the brace is also screwed to the top. Solid as a rock.
Inset presses at bench level means no bending/stretching, everything within arms reach and the press doesn't get leverage on the bench.
Either your bench beats the press, or your press beats the bench...
I hate it when benches slapping the wall or 'walk' across the floor.
No hip/elbow busters either!
If the entire room was dedicated to reloading, it might be different, but this is a hobby and such I don't care to dedicate a room to reloading I have to serve & support.
If reading made me money & served me, it would be different, but it doesn't.
I use the design with my little case processing equipment since it's cheap & easy to build and works quite well...
These machines are mounted on plates, so they don't torque the bench/top like a pump handle press does, so this particular bench doesn't need an extra under top brace.
Left, case neck qualifier, 95% open necks or better, no kinks means no splits, ejects blanks, loaded rounds, .204 Ruger, .222 etc.
Middle, case roller. Restores the extraction rim & groove, takes lower case bloat out from sloppy chambers (something no top down die can do),
Right, slow driven Dillon Super 1050, slow drive because the trimmer needs time to work, and the shoulder (Datum length) gets back to where it belongs.
The drawer under the top has all the spare parts, stuff I'm not using currently, and caliber changes.
Still PLENTY of storage on the floor under the bench for buckets & other misc. stuff, 8 sq.ft. footprint and moves easily on a roller dolly.
Casters could easily be installed, but I like it sitting solidly on the floor.
When you reload at home and can stop/walk away when it suits you, standing over a conventional bench with raised press might be OK.
I'm disabled, replacement knees, one hip, enough exotic metal in my back to build a small spacecraft out of, so I sit and I want to reach everything from a comfortable, supportive chair...
AND,
When I'm processing brass as a business it's several hours at a JOB, no getting up and walking off.
The bench tops/presses are at optimum height for me sitting in a supportive chair.
When manually operated, the handle is never higher than my shoulder, and I never have to lean forward and 'Stoop' to complete the stroke.
Feet are flat on the floor, chair has a backrest, and is solid, good for hours without damaging myself or 'Limp Wristing' or short stroking the press.
The XL650 loads MUCH better quality, more consistent ammo than the 1050, while the 1050 has the strength/rigidity to whip stubborn brass.
Brass going back into the same firearm doesn't need a lot of bending, but general brass and milbrass takes a TOUGH press to beat it.
With a little tuning, I haven't seen a 650 that won't produce match grade ammo and decent dies.
Last edited: